For the past many years, there have been many forms of the game of pool in existence. The fact that there have been various changes to the materials that the game is comprised has not had an effect on the felt cover. It is one aspect that has remained the same over time. However, it has a short lifetime that means it has to be replaced over and over after some time. In consideration of pool table refelting Denver residents should be acquainted with the basic of the procedure.
There are various materials needed for the procedure to be done successfully. Some of these include a staple gun, hammer, rag, felt, socket wrench and cleanser. The procedure starts with removal of the staples which surround the pockets at the underside part of the table. Next, the nails that secure the rails on the underside will need to be gotten rid of. Three bolts should be removed for every rail.
The rails are taken off after all bolts have been removed. The pocket liners are then detached as necessary. The staples attaching the felt to the rail cushions are pulled out. This is followed by removal of the felt that covers the cushions. The felt is then removed from the tabletop. It will be important to determine whether the felt is stapled or glued. At times it is both stapled and glued. A staple puller is used for pulling individual staples from the felt. Peeling of the glued felt from the tabletop needs to be done gently.
What follows next is preparing the felt for re-felting. All the holes and cracks are then filled with pool table wax. The wax will be left to wax for one minute or so before any excess is scrapped off by the use of a putty knife. The slate surface is cleaned using a cleanser. Prior to being covered using the felt, it is advisable to leave the surface to dry completely.
The felt pieces that will be used have to be properly and accurately measured. This is followed by cutting them in accordance to the table dimensions. Failure to do the measurements and cutting accurately will lead to the table having an undesirable appearance.
The next process is normally very important. One will need to start stapling the fabric to the table. The process is started at the center of one short edge before proceeding to the corners. All this is done while remembering not to cover the pockets. When placing the staples, one needs to move in increments of about two inches while pulling the fabric taut. This is done for all the sides of the table.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
The felt is used to line the rails. In order to know the size of the felt pieces to be used, the rail design should be observed. The rails are then reattached to the table. Replacement of the pockets and liners is the last process.
There are various materials needed for the procedure to be done successfully. Some of these include a staple gun, hammer, rag, felt, socket wrench and cleanser. The procedure starts with removal of the staples which surround the pockets at the underside part of the table. Next, the nails that secure the rails on the underside will need to be gotten rid of. Three bolts should be removed for every rail.
The rails are taken off after all bolts have been removed. The pocket liners are then detached as necessary. The staples attaching the felt to the rail cushions are pulled out. This is followed by removal of the felt that covers the cushions. The felt is then removed from the tabletop. It will be important to determine whether the felt is stapled or glued. At times it is both stapled and glued. A staple puller is used for pulling individual staples from the felt. Peeling of the glued felt from the tabletop needs to be done gently.
What follows next is preparing the felt for re-felting. All the holes and cracks are then filled with pool table wax. The wax will be left to wax for one minute or so before any excess is scrapped off by the use of a putty knife. The slate surface is cleaned using a cleanser. Prior to being covered using the felt, it is advisable to leave the surface to dry completely.
The felt pieces that will be used have to be properly and accurately measured. This is followed by cutting them in accordance to the table dimensions. Failure to do the measurements and cutting accurately will lead to the table having an undesirable appearance.
The next process is normally very important. One will need to start stapling the fabric to the table. The process is started at the center of one short edge before proceeding to the corners. All this is done while remembering not to cover the pockets. When placing the staples, one needs to move in increments of about two inches while pulling the fabric taut. This is done for all the sides of the table.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
The felt is used to line the rails. In order to know the size of the felt pieces to be used, the rail design should be observed. The rails are then reattached to the table. Replacement of the pockets and liners is the last process.
About the Author:
You can visit www.anytimebilliards.com for more helpful information about Steps Of Pool Table Refelting Denver.